Delphi NA10000-11B1 - Mobile Navigation - GPS Receiver User Manual download pdf (Page 12)

Suction or adhesive mount to dash

1.Choose a position on the dash where Delphi

Mobile Navigation will be clearly visible to the driver

without obstructing the driver’s view.

2.Thoroughly clean and dry the suction cup and the

mounting area of the dash.

3.Suction mount: If the location is flat enough, you can

simply use the suction cup to mount the unit directly

onto the dash. If the suction cup does not adhere,

clean the mounting area with a cloth dampened with

isopropyl alcohol. Let the area dry, then reapply the

suction cup.

Adhesive mount: If the location is not suitable to use

the suction cup alone, use the suction pad to provide

a flat surface for the suction cup. Peel the protective

layer off the adhesive tape on the bottom of the

suction pad. Press the suction pad onto the desired

position on the dash and hold firmly for 30 seconds.

8.Snap Delphi Mobile Navigation onto the socket clip.

First, position the two locating tabs (found on the

bottom of the unit) into the corresponding slots on the

socket clip. Then, snap the top side of Delphi Mobile

Navigation onto the clip.

9.Flip the GPS antenna outward so that the antenna

points horizontally.

10. Plug the 12/24V power adaptor into the cigarette

lighter socket.

11. Plug the other end of the power cable into the

socket on the left side of Delphi Mobile Navigation.

12. Verify that Delphi Mobile Navigation is positioned such

that the GPS antenna has a clear view of the sky.

Note: In most vehicles, you will need to have the engine idling in order to

program your destination. You also can turn on the unit with just the

accessory power (i.e., your ignition key turned to the ACC “on” position).

When you turn on the engine, power may be interrupted to the unit but

the programmed destination will be saved. In vehicles where accessory

power is on permanently, the unit can be turned on and programmed as

soon as the power adaptor is connected. Turning on the engine will not

reset the unit.

To unclip Delphi Mobile Navigation from the mounting bracket, press

down on the back of the upper plastic clip. Release the top of the

unit. Then lift the unit out of the bottom two slots.

Warning: To avoid personal injury, follow the safety guidelines and

installation instructions provided so that Delphi Mobile Navigation does

not obstruct the view of the driver, interfere with the operation of any airbags

and safety features in the vehicle, or become airborne in the case of an acci-

dent. Do not attempt to install the Delphi Mobile Navigation unit while driving.

You can remove the adhesive mount from your dash by taking

the following steps:

1. Lift one edge of the suction pad gently with fingers or the

rounded edge of a spoon. Once enough of the edge is loos-

ened to grip with your fingers, pull the pad gently from the

mounting surface at a 90-degree angle. Avoid using sharp

tools that could damage the car interior.

2. If the pad fails to loosen, first warm it with a hair dryer for

2 minutes to 3 minutes to soften the adhesive. Be careful

not to apply too much heat, which could damage the

mounting surface.

3. If any adhesive remains on the dash surface, the adhesive can

easily be removed by rubbing your thumb or finger across it.

4. As necessary, use a mild household cleaner to clean the

dash surface.

Caution: Never use a commercial heat gun or paint-stripping gun.

This could result in damage to the unit or to your vehicle.

Antenna points

up and out

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 39 40

Comments to this Manuals

No comments

Delphi NA10000-11B1 - Mobile Navigation - GPS Receiver User Manual Page 12

Comments to this Manuals

Related products and manuals for Navigators Delphi NA10000-11B1 - Mobile Navigation - GPS Receiver